|
产品说明 Description |
|
聚氨酯磁漆IS33是一种高光泽的脂肪族聚氨酯双组分涂料，具有优异的户外耐候性、保光性和保色性，漆膜坚韧，耐磨损、耐碰撞。
Polyurethane enamel IS33 is a two-component, high-gloss polyurethane coating with excellent outdoor weatherability, optimum floss and color retentions. It forms a hard and tough film resistant to abrasion and impact. |
|
主要特性 Outstanding Characteristics |
|
作为长效装饰面漆，涂用在严重腐蚀环境中的钢结构表面。
可涂装在非铁金属，混凝土、水泥石棉板、木板、聚酯及其他钢性表面。
可作为机械、机床等设备的装饰面漆。
As a long-term decorative topcoat on steel structure in severely corrosive environment.
On the rigid surfaces of non-ferrous metal, concrete, asbestos-cement board, plank, polymeric ester.
As advanced decorative topcoat on the machinery and machine tool etc. |
|
技术数据 Technical Data |
|
漆 面:
Finish: |
高光
High gloss |
|
|
颜 色:
Colors: |
各色
A wide range of colors |
|
|
体积固体含量:
Volume solids: |
约50%
Approx. 50% |
|
|
理论涂布率:
Theoretical spreading rate: |
约10.6米2/升
Approx. 10.6 m2/L |
(以50微米干膜计)
(50 micron dry film thickness) |
|
耐 温：
Temperature resistance: |
（干燥）：140℃
Maximum (dry)： |
|
闪 点:
Flash point: |
31℃
|
|
|
比 重:
Specific gravity: |
约1.19千克/升
Approx. 1.19 kg/L |
|
|
指 触 干:
Dry to touch: |
约8小时
Approx. 8 hours |
|
|
完全固化:
Fully cured: |
7天 20℃
7 days |
|
|
施工详述 Application Details |
|
固 化 剂:
Curing agent: |
H380 |
|
混合比例:
Mixing ratio: |
基料IS33 : 固化剂H380 = 4:1 (体积比)
Base IS33 : Curing agent H380 = 4: 1 (by volume) |
|
施工方法:
Application method: |
无空气喷涂
Airless spray |
刷涂
Brush |
|
稀 释 剂:
Thinner : |
TH95 |
TH95 见“备注”
See remarks |
|
用量:
Max. Vol.: |
5%
|
5%
|
|
混合使用时间:
Pot life: |
2小时 20℃
2 hours |
|
|
漆膜厚度:
Indicated film thickness: |
湿膜: 100微米
Wet: .100 microns |
干膜: 50微米 见“备注”
Dry: 50 microns See remarks |
|
重涂间隔:
Recoat interval: |
最小:16小时 20℃
Min.: 16 hours |
: 见“备注”
Max.: See remarks |
|
施工条件:
Application conditions: |
施工表面要求清洁干燥，表面温度应高于露点以避免水汽凝结。固化温度为－10℃，在冰点或冰点以下施工会使表面结冰而影响漆膜的附着力。施工期间及施工后16小时内湿度太大、凝露会影响漆膜的良好形成。在狭窄空间内施工和干燥期间应提供足够的通风。 |
|
|
Apply on clean and dry surface. The temperature must be above the dew point to avoid condensation. Minimum temperature for curing is -10℃. As temperature at /below freezing paint, freezing may occur on the surface and influence the adhesion of the film. High humidity or condensation during application and the following 16 hours may adversely affect the film formation. In confined spaces provide adequate ventilation during application and drying. |
|
先涂油漆:
Preceding coat: |
环氧漆、环氧厚浆漆IH35,或按规定先涂。
Epoxy paint, epoxy hi-build paint IH35 or according to specification. |
|
加涂油漆:
Subsequent coat: |
无需加涂。
None. |
|
备注 Remarks |
|
|
施工温度约30℃以下时，建议使用稀释剂TH92, 若高于此温度, 建议用稀释剂TH95。可根据使用目的和部位修改漆膜厚度, 但这会改变涂布率、干燥时间和重涂间隔。
Thinner TH92 is recommended at application temperature below approximately 30℃. At high application temperatures thinner TH95 is recommended.
May be specified in another film thickness than indicated depending on purpose and area of use. This will alter spreading rate, drying time and recoat interval.
物理参数随温度的变化：（干膜厚度范围为40-60微米）
Normal range for dry film thickness: (40-60 micron.) |
|
|
温度变化的物理参数
Physical data versus temperature |
|
|
施工表面温度
Substrate temperature |
-10℃ |
0℃ |
10℃ |
20℃ |
30℃ |
|
|
|
指触干 ( 约 )
Dry to touch (Approx.) |
3 d |
36 h |
16 h |
8 h |
6 h |
|
|
|
施工后抗凝露、潮湿和微雨时间
Resist condensing, humidity/light
showers after application |
7 d |
3 d |
32 h |
16 h |
12 h |
|
|
|
完全固化 (相对湿度:70%)
fully cured ( 70% RH） |
2 months |
32 d |
14 d |
7 d |
5 d |
|
|
|
重涂间隔(自重涂)
Recoat interval
(by itself） |
最小
Min |
6 d |
3 d |
32 h |
16 h |
12 h |
|
|
|
Max. |
6 months |
6 months |
6 months |
3 months |
2 months |
|
|
|
|
|
重涂间隔与漆膜在使用期间受周期性浸渍、重露、大温差、化学品侵蚀的情况有关。在其它条件下无重涂间隔。任何情况下都要求涂漆表面要清洁，尤其是重涂间隔期长的表面，以确保漆膜间的附着力。可先用适当的清洁剂清洗，然后用高压淡水清除掉表面一切油污、油脂等。表面的盐渍用淡水冲洗。正式重涂之前应先取一小块漆膜作试验，检查其清洁度。若超过重涂间隔，要磨粗表面，以保证漆膜间的附着力。若用其他油漆重涂，根据其类型一般重涂间隔为1—3天（20℃）。固化剂H380很易受潮，应储存于干燥处，密封桶盖。启封固化剂桶时应小心高压。混合漆料中稍微一点水份也会减少混合使用时间并造成漆膜缺陷。 |
|
Recoat interval refers to surfaces exposed to periodical immersion, heavy condensation, great variation in temperature, chemical attack during service life of the coating system. Under other conditions no maximum recoat interval. A completely clean surface is mandatory to ensure intercoat adhesion, especially at long recoat intervals. Any dirt, oil and grease has to be removed with suitable cleaner followed by high pressure fresh water cleaning, salts to be removed by fresh water hosing. To check an adequate quality of the surface cleaning a test patch is recommended before actual recoating. If the maximum recoat interval is exceeded, roughening of the surface is necessary to ensure intercoat adhesion. In case of recoating with other paint materials maximum will be 1-3 days (20℃) depending on type. Curing agent H380 is sensitive to moisture. Store in a dry place and keep the can tightly closed until use. Open curing agent cans with caution as over pressure might exist. Even small tracks of water in the mixed paint will reduce the pot-life and result in film defects. |
|
安全 Precautions |
|
本产品在施工时应遵守有关的国家卫生，安全和环境标准及其法规。使用前应获取和咨询有关本产品的材料安全数据表。注意包装标签上的安全事项。如果你没有完全理解或你不能严格执行这些安全事项，不要使用本产品。
在施工和干燥期间要采取通风措施，维持溶剂蒸汽的容度在安全极限内，防止中毒或缺氧。小心避免与皮肤、眼睛接触。
All work involving the application and use of this product should be performed in compliance with all relevant national Health, Safety and Environmental standards and regulations.
Prior to use, obtain, consult and follow the Material Safety Data Sheet for this product concerning health safety information. |
|
Read and follow all precautionary notices on the Material Safety Data Sheet container labels. If you do not fully understand these warnings and instructions or if you cannot strictly comply with them, do not use this product. Proper ventilation measures must be provided during application and drying to keep solvent vapor concentrations within safe limits and to protect against toxic or oxygen deficient hazards. Take precautions to avoid skin and eye contact (i.e. Gloves, goggles, face masks, barrier creams etc.)
Actual safety measures are dependant on application methods and work environment.
|
|
附注 Other Notice |
|
本说明书有关数据是在标准条件下取得，实际使用时，环境条件可能与之略有不同，以上数据如有改变，以本公司说明书为准，恕不另行通知。
All information in this product data sheet is based on standard conditions and slight variation may occur with different conditions. All information in our company is subject to change without notice. |