|
产品说明 Description |
|
IP39为双组份富锌环氧聚酰胺固化的底漆。它具有漆膜坚硬、耐磨和耐候等特点。可以对局部破损区域提供阴极保护。
Epoxy zinc rich primer IP39 is a two component, polyamide cured epoxy zinc rich primer. It cures to a hard wearing and weather resistant coating. Provides cathodic protection of partial mechanical damage. |
|
主要特性 Outstanding Characteristics |
|
在中等至严重腐蚀环境下，用作钢板的长效通用底漆。
As a general purpose, long-time primer on steel in moderately to severely corrosive environment. |
|
技术数据 Technical Data |
|
固 化 剂:
Curing agent: |
H339
|
|
|
漆 面:
Finish： |
半光
Semi-flat |
|
|
颜 色:
Colors： |
红-灰色
Red-gray |
|
|
体积固体含量：
Volume solids： |
约46%
Approx. 46 % |
|
|
理论涂布率：
Theoretical spreading rate： |
约12.1米2/升
Approx. 12.1 m2/L |
|
|
耐 温：
Temperature resistance: |
（干燥）：160℃
Maximum (dry)： |
|
|
闪 点:
Flash point： |
30℃
|
|
|
比 重：
Specific gravity： |
约1.9千克/升
Approx. 1.9 kg/L |
|
|
指 触 干:
Dry to touch： |
约2小时
Approx. 2 hours |
|
|
完全固化:
Fully cured： |
1星期 20℃
1 week |
|
|
施工详述 Application Details |
|
固 化 剂:
Curing agent: |
H339
|
|
混合比例：
Mixing ratio： |
基料IP39:固化剂H339 =4:1
Base IP39 : Curing agent H339 = 4 : 1 |
体积比
By volume |
|
施工方法：
Application method： |
无空气喷涂
Airless spray |
空气喷涂
Air spray |
刷涂
Brush |
|
稀 释 剂 ：
Thinner： |
TH90 |
TH90 |
TH90 |
|
用量 ：
Max. Vol.： |
15%
|
15%
|
15%
|
|
混合使用间：
Pot life： |
8小时 20℃
8 hours |
|
|
漆膜厚度：
Indicated film thickness： |
湿膜: 40微米
Wet: 40 micron |
干膜: 20微米 见“备注”
Dry: 20 micron See remarks |
|
重涂间隔：
Recoat interval： |
见“备注”
See remarks. |
|
表面处理：
Surface preparation： |
用适当的清洁剂除去钢板表面上的油污和油脂，用高压淡水除去表面的盐迹和其他污物。表面喷砂清洁度至Sa2.5级标准, 粗糙度相当于Rugotest标准No3, BN9a。
Remove oil and grease with suitable cleaner. Remove salt and contaminants by high pressure fresh water cleaning. Abrasive blasting to Sa2.5 with a surface profile equivalent to Rugotest No.3, BN9a. |
|
施工条件：
Application conditions： |
仅在使施工和固化得以正常温度的条件下使用本品。施工表面的温度也应高于这两个限度。在冰点和冰点以下温度施工，应注意表面的结冰会影响漆膜附着力。油漆本身的温度应高于15℃。为避免水汽凝结,应在干燥清洁而温度又高于露点的表面上施工。
在狭窄空间内施工和干燥期间, 应大量通风。
The surface temperature should also be above this limit. As temperature at / below freezing point, freezing may occur on the surface and influence the adhesion of the film. The temperature of the paint itself preferably be above 15℃. Apply only on a clean and dry surface with a temperature above the dew point to avoid condensation.
Provide adequate ventilation during application and drying in confined spaces. |
|
加涂油漆：
Subsequent coat： |
参阅“备注”
See remarks. |
|
备注 Remarks |
|
可根据使用目的及部位修改漆膜厚度，但这会相应改变涂布率、稀释量、干燥时间和重涂间隔。漆膜厚度的正常范围为：15-50微米。
注意：建议不要在绝缘涂层后使用富锌底漆。
May be specified in another film thickness than indicated depending on purpose and area of use. This will correspondingly alter spreading rate and may influence amount of thinning, drying time and recoat interval. Normal range for film thickness: 15-50mm.
Attention: Do not use zinc-rich primer on the isolated coating. |
|
重 涂:
Recoat： |
重涂间隔与以后的暴露条件有关。
Recoat interval is related to exposure condition. |
|
20℃温度条件下的重涂间隔为 Recoat interval at 20℃ |
|
|
重涂的油漆品种
Recoat with |
最小
Min. |
Max. |
|
|
|
环氧漆系列
Epoxy series |
6 小时
6 hours |
30 天
30 days |
|
|
氯化橡胶厚浆漆 IS60
Chlorinated rubber hi-build paint IS60 |
6 小时
6 hours |
24 小时
24 hours |
|
|
|
重涂间隔仅适用于漆膜在使用期间受周期性浸渍、重露、大温差、化学品侵蚀和磨损的情况。如果超过重涂间隔,必须磨粗表面以确保漆层间的附着力。如果施工表面在重涂之前曾暴露于污染环境，则在重涂前应用高压淡水彻底清洗表面，并任其自干。此外，还必须用硬刷子刷除锌蚀物(白锈)。 |
|
|
The maximum recoat interval refers to surfaces exposed in periodical immersion, heavy condensation, and great variation in temperature, chemical attack and/or abrasion during service life of the coating system. If maximum recoat interval is exceeded, roughening of the surface is necessary to ensure intercoat adhesion. If the surface exposed to contaminated environment prior to overcoating, thoroughly hose down the surface by high-pressure fresh water and allow drying. In addition, scrubbing with a stiff brush to remove zinc corrosion products (white rust). |
|
安全 Precautions |
|
本产品在施工时应遵守有关的国家卫生，安全和环境标准及其法规。使用前应获取和咨询有关本产品的材料安全数据表。注意包装标签上的安全事项。如果你没有完全理解或你不能严格执行这些安全事项，不要使用本产品。
在施工和干燥期间要采取通风措施，维持溶剂蒸汽的容度在安全极限内，防止中毒或缺氧。小心避免与皮肤、眼睛接触。
All work involving the application and use of this product should be performed in compliance with all relevant national Health, Safety and Environmental standards and regulations.
Prior to use, obtain, consult and follow the Material Safety Data Sheet for this product concerning health safety information.
Read and follow all precautionary notices on the Material Safety Data Sheet container labels. If you do not fully understand these warnings and instructions or if you cannot strictly comply with them, do not use this product. Proper |
|
ventilation measures must be provided during application and drying to keep solvent vapor concentrations within safe limits and to protect against toxic or oxygen deficient hazards. Take precautions to avoid skin and eye contact (i.e. Gloves, goggles, face masks, barrier creams etc.)
Actual safety measures are dependant on application methods and work environment.
|
|
附注 Other Notice |
|
本说明书有关数据是在标准条件下取得，实际使用时，环境条件可能与之略有不同，以上数据如有改变，以本公司说明书为准，恕不另行通知。
All information in this product data sheet is based on standard conditions and slight variation may occur with different conditions. All information in our company is subject to change without notice. |