|
产品说明 Description |
|
自流平地坪漆IF38为无溶剂、漆膜致密的自流平环氧地坪涂料。
Self-flowing floor paint IF38 is a solvent-free, self-leveling, film compact epoxy floor coating. |
|
主要特性 Outstanding Characteristics |
|
作为在腐蚀严重、车辆往来、化学药品等环境中的表面保护涂料，用于工厂、仓库、汽修车间等的地面保护。
As surface protective coating in severely corrosive, traffic, chemical environment for ground protection in factory, warehouse, motor repair shop etc. |
|
技术数据 Technical Data |
|
漆 面:
Finish: |
高光
High gloss |
|
颜 色:
Colors: |
灰色 （可根据需要提供其他颜色）
Grey (other colors are available on request.) |
|
体积固体含量:
Volume solids: |
100% |
|
理论涂布率:
Theoretical spreading rate: |
3升/米2（以干膜3毫米计）
3L/m2 (3mm DFT) |
2升/米2 干膜2毫米
2L/m2 (2mm DFT) |
1升/米2 干膜1毫米
1L/m2 (1mm DFT) |
|
闪 点:
Flash point: |
100℃
|
|
比 重:
Specific gravity: |
约1.17千克/升 不含混凝料IF81
Approx. 1.17kg/L No Concrete IF81 |
|
指 触 干:
Dry to touch: |
24小时
24 hours |
|
完全固化:
Fully cured |
7天
7 days |
|
储存稳定性:
Shelf stability |
1年 20℃
1 year |
|
施工详述 Application Details |
|
混合比例:
Mixing ratio |
A:
|
基料IF38:固化剂H332 = 100:55
Base IF38 : Curing agent H332 = 100 : 55 |
(重量比）
( by weight ) |
|
B: |
基料IF38:固化剂H332:混凝料IF81 = 100:55:109
Base IF38 : Curing agent H332 : Concrete IF81 = 100 : 55 :109 |
(重量比）
( by weight ) |
|
使用期:
Service life |
1小时 （20℃,10升）
1 hour (20℃, 10L ) |
|
施工工具:
Application tools |
耙、去泡辊
Rake, antifoam roller |
|
工具清洗:
Cleaning of tools |
稀释剂TH90
Thinner TH90 |
|
漆膜厚度:
Indicated film thickness: |
湿膜:3毫米
Wet: 3mm |
干膜:3毫米
Dry :3 mm |
|
重涂间隔:
Recoat interval: |
最小: 36小时
Min: 36 hours |
20℃ |
:3天 20℃
Max.: 3 days |
|
预涂油漆:
Precoating |
环氧封闭漆IF30
Epoxy Sealer IF30 |
|
施工条件:
|
在施工和固化时，环境温度应超过10℃，油漆温度在15℃左右，在施工前后及施工时应避免水汽凝聚。 |
|
Application conditions: |
Temperature must be above 10℃during application and curing. The temperature of paint
itself, preferably, 15℃or so. Condensation must be avoided before, after and during application. |
|
施工方法:
Application method: |
混合时使用低速搅拌器。混合步骤是：
1. 先将基料倒入容器中；
2. 边搅拌边加入混凝料；
3. 最后加入固化剂。
低速混合10分钟后，本品即可施工。考虑数量、面积的大致比例，将本品倒向地面，使用带三角齿的耙子，将油漆铺平。齿深根据自流平后的漆膜厚度而定。施工30至45分钟后，用去泡辊消除残留空气。在此涂层上行走时，要求穿用特殊的钉鞋。
Use low-speed agitator during mixing. Steps are:
1. Pour the base into the container;
2. Add concrete with constant mechanical stirring;
3. Finally add curing agent.
The application can proceed 10 minutes after low-speed mixing. In rough proportion of amount an area, pour the mixture to the ground and smooth it with a triangle teeth rake. The teeth depth is dependent on film thickness after self-flowing. Remove residual air with an anti-foam roller 30-40 minutes after application. Special spikes must be worn on the coating. |
|
后涂油漆:
Subsequent coat: |
无，或者加涂不含混凝料的本品。
None or IF38 free of concrete. |
|
备注 Remarks |
|
可以根据使用的目的及部位改变漆膜厚度。随之涂布率、重涂间隔和干燥时间也会相应改变。本品无重涂间隔。如重涂前施工表面受过污染，须用高压淡水冲净表面, 任其自干后，再进行重涂。
潮湿表面定义：表面上有水分但肉眼不易看出。
May be specified in another film thickness than indicated, but this will alter spreading rate, recoat interval and drying time. No maximum recoat interval. If surface has been contaminated before recoating thoroughly clean the surface by high pressure fresh water hosing and allow to drying prior to final coating.
Definition of damp surface: Damp surface is the surface on which water is not readily detectable. |
|
安全 Precautions |
|
本产品在施工时应遵守有关的国家卫生，安全和环境标准及其法规。使用前应获取和咨询有关本产品的材料安全数据表。注意包装标签上的安全事项。如果你没有完全理解或你不能严格执行这些安全事项，不要使用本产品。
在施工和干燥期间要采取通风措施，维持溶剂蒸汽的容度在安全极限内，防止中毒或缺氧。小心避免与皮肤、眼睛接触。
All work involving the application and use of this product should be performed in compliance with all relevant national Health, Safety and Environmental standards and regulations.
Prior to use, obtain, consult and follow the Material Safety Data Sheet for this product concerning health safety information.
Read and follow all precautionary notices on the Material Safety Data Sheet container labels. If you do not fully understand these warnings and instructions or if you can not strictly comply with them, do not use this product. Proper ventilation measures must be provided during application and drying to keep solvent vapor concentrations within safe limits and to protect against toxic or oxygen deficient hazards. Take precautions to avoid skin and eye contact (ie. Gloves,
goggles, face masks, barrier creams etc.)
Actual safety measures are dependant on application methods and work environment. |
|
附注 Other Notice |
|
本说明书有关数据是在标准条件下取得，实际使用时，环境条件可能与之略有不同，以上数据如有改变，以本公司说明书为准，恕不另行通知。
All information in this product data sheet is based on standard conditions and slight variation may occur with different conditions. All information in our company is subject to change without notice. |