产品名称：35W普通汽车HID安定器
产品型号：MS-001
出品单位：美日电子
产品详细介绍；
一 主体: L85×Ｗ72×Ｈ30 mm
颜色: 黑色或银色
配件:挂片包一套
二 HID工作参数.
输入电压: 8.0---16V DC
启动电流: 7.5A
额定工作电压: 13.5V DC
额定工作电流: 4.2A
恒功率输出: 50±1W
启动特性: 1秒达到20%亮度,6达到额定亮度,20秒内达到稳定电流.
过压保护: 工作电压大于是16V时,产品进入保护状态,保护电流≤0.06A.
短路保护: 当灯管输出线路出现短路时,产品进入保护状态,保护电流≤0.06A.
输出开路保护: 当灯管出现断裂时,产品进入保护状态,保护电流≤0.06A
逆向保护: 当电源正负极接反时,产品不会工作.保护电流等于0.00A.
三 HID必检项目.
外观: 表面光滑无刮花,无变形,破损.
连接线无破裂,无变形,插头连接应牢固,不得脱开,松动.
绝缘测试: 对地绝缘电阻≥100MΩ
开路测试: 输出处于开路状态,接通12V DC,高压输出放电在1—2秒内停止,进入自动保护状态.
短路测试: 输出处于短路状态,接通12V DC, 在持续0.5—1秒后,进入自动保护状态.
工作电流: 输入12V DC 冷态启动电流为:≤7.5A;稳定电流为:4.2±0.5
热启动测试: 稳定工作5分钟后持续启动5次无障碍,并且热启动电流:≤5.5A:
反向测试: 当输入12 V DC 反接时产品无法进入工作状态.
低压测试: 当电压从0伏升至7.5----9V时,HID灯要能顺利点亮.
过压保护: 当电压升至于17—18V时,产品进入保护状态.
损耗测试: 灯管功率应稳定在:50±1W,镇流器损耗功率在:6±1W.
复光性测试: 灯管功率应稳定在9V的电源电压下能正常工作启动点灯.
表面温度测试: 将镇流器与HID灯连接在常温下点灯1小时之后,镇流器表面温度不得超60℃.
防水性能: 将镇流器浸在水100CM的水下,水温为常温,浸泡0.5小时后点灯测试功能正常.
高低温性能: 将镇流器放在温度为:-40℃-- +85℃的环境下镇流器应能正常工作.
Product Name: 35W General Automotive HID Ballast
Model: MS-001
Production units: the United States Sterling Electronics
Product details;
A main: L85 × W72 × H30 mm
Color: black or silver
Parts: a set of hanging bag
Second HID operating parameters.
Input voltage: 8.0 --- 16V DC
Maximum starting current: 7.5A
Rated operating voltage: 13.5V DC
Rated current: 4.2A
Constant power output: 50 ± 1W
Startup characteristics: 1 seconds to reach 20% brightness, 6 to achieve the rated brightness, 20 seconds to achieve a stable current.
Over-voltage protection: 16V operating voltage was large, the products to enter the protection, the protection of current ≤ 0.06A.
Short-circuit protection: When the lamp output circuit short-circuit, the products to enter the protection, the protection of current ≤ 0.06A.
Output open circuit protection: When the lamp fault occur, the products to enter the protection, the protection of current ≤ 0.06A
Reverse Protection: When the power is negative when anti-access, the product will not work. The protection of current equal to 0.00A.
HID three projects will be seized.
Appearance: smooth surface without scratches, no deformation, damage.
No broken links, non-deformation, plug connection should be firm, and shall not be torn off and the loose.
Insulation test: to-ground insulation resistance ≥ 100MΩ
Open-circuit test: output in the open state, connected to 12V DC, high-voltage discharge output stopped in 1-2 seconds, into the automatic protection.
Short-circuit test: output in the short-circuit state, connected to 12V DC, in the continuing 0.5-1 seconds after entering the auto-protection.
Operating current: 12V DC input current of Cold Start: ≤ 7.5A; stability current: 4.2 ± 0.5
Hot-start test: the stability of the work of five minutes to start after 5 continuous barrier-free, and hot-start current: ≤ 5.5A:
Reverse-test: 12 V DC input reverse when products can not enter the working state.
Low pressure test: When the voltage from 0 V up to 7.5 ---- 9V when, HID lamps to be lit smooth.
Over-voltage protection: When the voltage was increased to 17-18V, the protection of the state of products.
Loss test: lamp power should be stable at: 50 ± 1W, ballast power loss: 6 ± 1W.
Fuguang test: lamp power should be stable at the power supply voltage of 9V to activate the lights to work.
Surface temperature of the test: will be connected ballasts and HID lamp light at room temperature 1 hour after the surface temperature may not be super ballast 60 ℃.
Waterproof performance: will be immersed in water ballast 100CM underwater, the water temperature to room temperature, 0.5 hours after the light soaking test function.
High and low temperature performance: the ballast on the temperature: -40 ℃ - +85 ℃ environment ballast should be able to work properly.